LAUNCH X431

 Is there any way to change the Launch X431 scanners' username and password without doing a factory reset? Users are allowed to change the registered email and password, you cannot change user name. How to change email address? User Info->Profile, input new email address and Bind email. How to retrieve password? Step 1: Log in X431 App Stay in the main page and click User Info Step 2: Select Profile click Retrieve password to get back your account Step 3: Retrieve user name and password Enter device serial number, the system will show your user name directly Get verification by email which is from your registration information Set your new password again, click Reset password www.x431shop.eu

  Launch X431 Pro Elite and Launch X431 Pros V5.0 are both new products released by LAUNCH in 2023, both using the latest hardware configurations. To differentiate between these two products, we have put together a table: Conclusion: The hardware configurations of Launch X431 Pro Elite and X431 Pros V5.0 are basically the same, with only a slight difference in battery capacity. Launch X431 Pros V5.0 requires purchasing a license when using VAG Guided Functions. X431 Pro Elite does not require additional payment when using VAG Guided Functions. Launch X431 Pro Elite supports 32+ reset function, X431 Pros V5.0 supports 37+ reset function. www.x431shop.eu

  Problem: I had a problem updating my Launch CRP429C obd2 scanner . When i press update, it said serial has not been registered. Any clue? Solution: Usually network issue. Change another network and try again. If still the same problem happens, clear cache or reset to factory setting, then update software again. www.x431shop.eu

 Today we're going to use Launch X431 V & GODIAG GT100 to diagnose ME17.9.11 ECU for a test. The GODIAG can covert the car OBD2 interface into 16pin that allows to connect single modules and any diagnostic tools. Compatible with Launch X431 V+ , X431 PRO5 , etc. Connection Connect GODIAG GT100 & X431 V VCI; Connect ECU according to wiring diagram, includes PIN5, 18, PIN79, PIN57. Finally connect the power supply. Diagnostic Test Now we can start diagnosing. Local Diagnose >> EOBD/OBDII >> OK >> ENTER >> Read I/M Readiness(Mode 01) >> Ready status after DTCS cleared >> Secondary air system monitor >> Ready status after DTCS cleared Here we can read I/M readiness, live data, freeze frame, read & clear fault code, on-board monitoring test, control operation of on-board component/system, read vehicle information and EU OBFCM. Read live data(mode 01) Read freeze frame data(mode 02) Read fault code(mode 03/07...

  Question: Does launch x431 x-prog3 immo programmer works with xdiag, prodiag, xpro5 or diagzone software activations? Launch X431 Xprog3 (GIII) works with X-diag (via Bluetooth) and also with Diagzone (via Bluetooth and usb connection). BUT Xdiag wont open generated Key file for Benz Key. Same problem with BMW Key. Prodiag cannot calculate It online. X-DIAG 3.14.057 can make online calculation with x-prog3 adapter . Updating till 7.0.001 not work all online function like Key calculation, coding etc. To work with xprog most stable Is x-diag .057, even if has Major bug in opening files. It works with prodiag as well. Prodiag provide usb connection with virtual comport. It also work with Xpro5 too. Diagzone working online, Xpro5 work online too. Some got both PAD VII and DBScar with Diagzone, they say x-prog3 with DZ are useless comparing PAD VII.

 What's the difference between the new smartlink and old smartlink VCI of Launch X431 PAD VII ? X431shop.eu has two version Smartlink C, it will sent Randomly. Function is exactly the same. Old smart link is based on Android system and new VCI is based on Linux. New smartlink is faster.

 The latest CRP series of LAUNCH X431 is CRP919 , and older models support software updates. Here is the details picture guide for the update. 1.Click OK Click Renewal click " Subscription Renewal Card" Input the 24 subsription renewwal card pin code and submit And you'll see the update expired 1 year, update success! If you also have the problem update your Launch scanner, follow this way, it will help www.x431shop.eu

 This is a tutorial on how to do Subaru anti-theft mechanical key adding with LAUNCH X431 IMMO Plus / X431 IMMO Elite via OBD. Follow the operation below to learn step by step. Connect X431 IMMO programmer to OBD. IMMO >> Subaru >> Immobilizer key matching >> Japan >> Smart Scan Check if the ignition switch is turned ON. Door close. Press OK. Number of registered access key(s) >> Yes Registered key(s)=1 Number of registered key(s) inspection ended. Turn OFF the ignition switch and remove the key. Press OK. Immobilizer system registration >> Yes Check if the ignition switch is turned ON. Press OK X431 IMMO PLUS shows: This key has been registered. Number of registered key(s)=1 Please follow the instructions: Please prepare an unregistered key if desired then turn ON the ignition switch with the key. [NOTE: Please carry out within 30 seconds.] The number of registered key(s) has changed: 2 Processing… Communicat...

  Problem: I received the Launch X431 PAD VII elite scanner and tried to hook it up to a BMW. But the new smartlink VCI cannot communicate with tablet. Error images attached. Any suggestion? Solution: Double check if the adapters are well connected. If yes, connect the tablet and smartlink VCI with vehicle and charge for half an hour. Restart PAD VII after half and hour. It should be fine.

 What is the difference between Launch X431 V 4.0 and Launch X431 Pro Elite diagnostic scanner ? Check table comparison below: In sum: X431 V 4.0 is Bluetooth version while Pro Elite connects via USB cable ONLY. Launch X431 Pro Elite does not do online ECU coding , only offline coding. X431 V will do both online & offline coding. Pro Elite has built-in CAN FD & DoIP protocols for new GM JLR Porsche models, X431 V does not (need extra adapter). Pro Elite has newer operating system, large space, larger battery. www.x431shop.eu

  Problem: I got the Launch X431 PAD VII Elite and install j2534.exe program on my laptop. When i try to update smartlink c, it failed me and said Write upgrade failed (error_id1004 MoveFile). Smartbox j2534 passthru is connected and detected. Any suggestion? Solution: Download smartbox J2534 driver and install again. https://en.cnlaunch.com/products-detail/i-223.html