LAUNCH X431

 If Nissan vehicle displays DTC: "P181F-01" during scanning, it can be resolved using the LAUNCH X431 diagnostic tool . First, you need to perform the Unit Characteristics Writing function, and then clear the fault code. This article will explain how to do this. Function Description : After replacement of control units, there is related DTC: P181F-01 Calibration not completed. In this case, you need to execute this " Unit Characteristics Write " function. Attention : 1. If the "DTC Confirmation Step" has been performed previously, be sure to turn the ignition switch to the OFF position and wait for at least 10 seconds before performing subsequent tests. 2. The 12-digit code written must be on the rear axle of the car, as shown in the following figure. Diagnostic device used : LAUNCH X431 PAD V ELITE ( X431 PRO series and PAD series can also refer to this step). Software Requirements : Nissan V44.70 and later version Test Vehicle Module :...

 The LAUNCH X431 series diagnostic tools support 37+ special functions, including "Reset Angle Offset": This function needs to be performed for reset when the vehicle is replaced with a BSM or EPS ECU. This article will take FIAT vehicles as an example (SGW needs to be unlocked) to introduce how to operate. Supported Products : Launch PRO or PAD series comprehensive diagnostic equipment. X431 PRO series: X431 PROS V / X431 V+ / X431 PRO ELITE / Pros Elite / X431 V / PRO3 V+ Elite X431 PRO3S+ / Pro3 ACE / Pro3 APEX / X431 PRO5 X431 PAD series products: X431 PAD V ELITE / X431 PAD VII ELITE The equipment used in this article : LAUNCH X431 PAD V ELITE Tested model : 2023 — Fiat — Fastback. VIN: 9BD376A31PYB***** Note: Diagnosing 2019 and later FIAT vehicles requires unlock the SGW, so an FCA account is required. For more information, please see this article: How to Unlock the FCA SGW by LAUNCH Diagnostic Tool Operation process : 1. On a X431 PAD V E...

  LAUNCH X431 full range of diagnostic tools supports backup battery timer reset, this article will demonstrate how to use X431 PAD V to perform a backup battery timer reset on a GM Chevrolet Blazer. (X431 PAD V supports topology map function, if diagnostic devices without topology map function need to enter from the special function menu). Function description : This function is used to reset the backup battery timer. Current equipment : LAUNCH X431 PAD V . Tested model : 2020 Chevrolet Blazer VIN: 3GNKBJR45LS6***** Operation process: 1. It is necessary to stop the vehicle before performing this function, connect the LAUNCH X431 PAD V to the vehicle. On PAD V, choose [Local Diagnose]. 2. Choose [GM] to test. Then, choose [Automatically Search] to identify car models automatically. 3. Click [Smart Detection] to scan the entire vehicle systems. 4. Click [TCICM (Telematics Communication Interface Control Module)] to access the system. 5. Then select the func...

 How to do Throttle Position Actuator Test on diesel heavy-duty trucks with LAUNCH-X431 PAD V Elite ? In this article, we’re testing on Foton Rowor as an example step by step. Local Diagnosis >> VIN Scan >> Engine System >> OK >> Actuator Test >> Throttle Position Actuator Test Note: The Actuator Test Requires T15 Power-On; The Engine Speed is 0; The Vehicle Speed is 0; The Test Time Will Automatically Stop After More Than 30s! Click OK. Throttle Position Actuator Test >> Settings >> Input The Value: 50 Click OK. Execution successful. Done. www.x431shop.eu

  LAUNCH-X431 PAD V ELITE supports ADAS function and can perform static calibration of the front camera of BYD 2023 Yuan PLUS EV. Users can refer to this process for operation. Function Description: This function is used to perform static calibration of the front camera for Yuan PLUS EV. This function needs to be executed when the following situations occur: 1. The front camera or multifunction video controller is replaced. 2. The front windshield is replaced. 3. The body structure is changed and the chassis is adjusted. 4. There are DTCs related to no-calibration. Before executing this function please make sure: The ADAS device is activated. The target and target placement tool are available. The calibration site is suitable. The ignition switch is in the ON position. The diagnostic instrument is connected to the network. Procedure: 1. On an X-431 PAD V , choose [Local Diagnose], and then choose [BYD] for testing. 2. Choose the latest BYD software upgrade ver...