How to set up LAUNCH SmartLink VCI WiFi connection

 SmartLink VCI is the latest diagnostic module from LAUNCH Company. It can be used with most LAUNCH diagnostic tools and supports Bluetooth, WiFi, USB and other communication methods. This article will introduce how to use SmartLink VCI’s WiFi connection.

Note: WiFi network latency is higher than that of wired network, and its anti-interference performance is worse. Therefore, it is recommended that users give priority to using wired network connection when doing remote diagnosis, especially online programming.

First, connect SmartLink to the power supply (connect to the vehicle OBD diagnostic port), and click [Settings] — -[WLAN] in the upper right corner of the SmartLink interface.


How to set up LAUNCH SmartLink VCI WiFi connection

Click [WLAN] and select WiFi connection, enter the WIFI name and WIFI password (if the WIFI password is not set, it can be ignored. The WIFI name is case-sensitive, please make sure it is consistent with the connected WIFI name), and then click [Connect]. Please note that SmartLink only supports 5G WiFi signals, not 2.4G signals.


How to set up LAUNCH SmartLink VCI WiFi connection
How to set up LAUNCH SmartLink VCI WiFi connection

If the WIFI connection is successful, click the button [Connected successfully, return to homepage] at the bottom of the interface to return to the homepage, and the device will automatically prompt whether to switch to super remote diagnostic mode. If you need the assistance of a remote technician to diagnose, please select YES; if you just perform the diagnosis yourself, please select NO


How to set up LAUNCH SmartLink VCI WiFi connection
How to set up LAUNCH SmartLink VCI WiFi connection
How to set up LAUNCH SmartLink VCI WiFi connection

If you need to switch to other WiFi hotspots after successfully connecting to WiFi, you need to restart the device and reconnect.

For tech support and best price Pls contact us:

WhatsApp: +86 15980495251

Email: Sales@x431shop.eu

www.x431shop.eu

Comments

Post a Comment

Popular posts from this blog

THINKCAR ThinkDiag unable to connect via Bluetooth?

Image
 My THINKCAR ThinkDiag device was unable to connect via Bluetooth and download software. The error message displayed was: "Polaczenie Bluetooth nie powiodlo sie, odtacz zlacze i sprobuj ponownie. PROBUJ PONOWNIE (Bluetooth connection failed. Please close the connector and try again. TRY AGAIN)." Solution: Fix Firmware: Navigate to "More" > "Firmware Fix" > " THINKDIAG Firmware Fix". Re-plug the Device: Unplug and then re-plug the THINKCAR OBD2 Scanner . Log in to your account again. Update the App: Ensure the ThinkDiag app is updated to the latest version. Outcome: The problem was resolved! I can now connect via Bluetooth and download the software normally. www.x431shop.eu
Read more

How To Update LAUNCH X431 GIII X-PROG 3 Software?

Image
 The Launch X431 GIII Software Update function keeps your diagnostic software & app up-to-date, you can also use it to customize your frequently used software. As a powerful chip reading and writing device, it's compatible with most X431 series tablets like X431 V+ , X431 PAD VII , X431 PRO5 , etc. How to update X-PROG 3 diagnostic software & APP? On the main diagnostic scree, tap "Software Update" to enter the update center. Check the software you want to upgrade, and then tap "Update". Once downloading completed, the software packages will be installed automatically. You will see below dialogue box once the installation is completed. Note: You may stop the process by tapping "Stop", and tap "Continue" to resume the process later. In case of network connection failure, tap "Retry". www.x431shop.eu
Read more

Solved! LAUNCH X431 PAD 7 Firmware Update Failed

Image
  Problem: The Launch X431 PAD 7 is failed to update firmware, I just follow all steps but nothing work. Ensure to update device firmware V1.5.5: Connect WIFI, ensure Internet is good. Update time will take 3 mins, ensure device with enough power at least remain more than 20 percent. Don't press POWER button while update. X431 PAD VII gives an error display: "Device no response, please retry" Please check the device whether connect success. Service busy, please retry later. What's the problem? Any ideas? Solution Please remember to connect PAD 7 with X-PROG 3 Key Programmer before upgrade. That's the reason why firmware update failed. Read also: How to update Launch X431 GIII X-PROG 3 software? Technical Support www.x431shop.eu
Read more