LAUNCH-X431 Pro3 ACE vs. Pro3 vs. Pro3s+ vs. Pro TT vs. Pro Dyno

 In addition to the latest Smartlink, LAUNCH diagnostic tool adapters also include DBscar VII. Currently, the main products using DBscar VII are: X-431 PRO3 ACE, X-431 PRO3 APEX, X-431 PRO3 (V5.0), X-431 PRO TT, X-431 PRO DYNO. This article will compare the differences between these products (Although the PRO3S+ (V5.0) has replaced the Smartlink, the functions are basically the same, so we also include it in this comparison).

Note: PRO3 ACE and PRO3 APEX are the same products customized by different dealers, with the same hardware and functions, and can be regarded as the same product (similar to CRP919E BT and CRP919X BT).


LAUNCH-X431 Pro3 ACE vs. Pro3 vs. Pro3s+ vs. Pro TT vs. Pro Dyno
LAUNCH-X431 Pro3 ACE vs. Pro3 vs. Pro3s+ vs. Pro TT vs. Pro Dyno
LAUNCH-X431 Pro3 ACE vs. Pro3 vs. Pro3s+ vs. Pro TT vs. Pro Dyno

From the chart we can see:

Pro TT and Pro Dyno are 8 inch tablets, Pro3 ACE, Apex, Pro3 V5 and Pro3s+ V5 are 10 inch tablets (there is a small rule for LAUNCH tablet devices, the higher the product, the larger the size, and the 10.1-inch PRO3S+ product is positioned higher than the 8-inch product).

They all support CAN FD and DoIP protocol (DoIP requires a DoIP cable).

They all cannot do online programming (no smartlink VCI).

Pro TT and Pro Dyno 8 inch tablets are not compatible with heavy duty modules, and do not support Topology mapping.

The new Pro3 V5.0 (aka V+ v5.0) now shares the same functions as Pro3s+ V5.0. Only appearance difference.

Comments

Post a Comment

Popular posts from this blog

THINKCAR ThinkDiag unable to connect via Bluetooth?

Image
 My THINKCAR ThinkDiag device was unable to connect via Bluetooth and download software. The error message displayed was: "Polaczenie Bluetooth nie powiodlo sie, odtacz zlacze i sprobuj ponownie. PROBUJ PONOWNIE (Bluetooth connection failed. Please close the connector and try again. TRY AGAIN)." Solution: Fix Firmware: Navigate to "More" > "Firmware Fix" > " THINKDIAG Firmware Fix". Re-plug the Device: Unplug and then re-plug the THINKCAR OBD2 Scanner . Log in to your account again. Update the App: Ensure the ThinkDiag app is updated to the latest version. Outcome: The problem was resolved! I can now connect via Bluetooth and download the software normally. www.x431shop.eu
Read more

How To Update LAUNCH X431 GIII X-PROG 3 Software?

Image
 The Launch X431 GIII Software Update function keeps your diagnostic software & app up-to-date, you can also use it to customize your frequently used software. As a powerful chip reading and writing device, it's compatible with most X431 series tablets like X431 V+ , X431 PAD VII , X431 PRO5 , etc. How to update X-PROG 3 diagnostic software & APP? On the main diagnostic scree, tap "Software Update" to enter the update center. Check the software you want to upgrade, and then tap "Update". Once downloading completed, the software packages will be installed automatically. You will see below dialogue box once the installation is completed. Note: You may stop the process by tapping "Stop", and tap "Continue" to resume the process later. In case of network connection failure, tap "Retry". www.x431shop.eu
Read more

Solved! LAUNCH X431 PAD 7 Firmware Update Failed

Image
  Problem: The Launch X431 PAD 7 is failed to update firmware, I just follow all steps but nothing work. Ensure to update device firmware V1.5.5: Connect WIFI, ensure Internet is good. Update time will take 3 mins, ensure device with enough power at least remain more than 20 percent. Don't press POWER button while update. X431 PAD VII gives an error display: "Device no response, please retry" Please check the device whether connect success. Service busy, please retry later. What's the problem? Any ideas? Solution Please remember to connect PAD 7 with X-PROG 3 Key Programmer before upgrade. That's the reason why firmware update failed. Read also: How to update Launch X431 GIII X-PROG 3 software? Technical Support www.x431shop.eu
Read more