LAUNCH-X431 IMMO PLUS Clone BMW DME Bench Tutorial

 This is a tutorial on how to clone BMW DME with LAUNCH-X431 IMMO PLUS by bench. You can also use LAUNCH-X431 IMMO ELITE to finish the job as well.


LAUNCH-X431 IMMO PLUS Clone BMW DME Bench Tutorial
LAUNCH-X431 IMMO PLUS Clone BMW DME Bench Tutorial
LAUNCH-X431 IMMO PLUS Clone BMW DME Bench Tutorial

Connect X431 IMMO PLUS, X-PROG3 & BMW module on bench.

IMMO >> BMW >> OK >> OK >> Engine Module Replacement >> BENCH Mode >> OK >> MSD81_TC1796 >> Connect

Connection succeeded.


LAUNCH-X431 IMMO PLUS Clone BMW DME Bench Tutorial
LAUNCH-X431 IMMO PLUS Clone BMW DME Bench Tutorial
LAUNCH-X431 IMMO PLUS Clone BMW DME Bench Tutorial

Backup EEPROM Data >> Save EEPROM file

Backup FLASH Data >> Save FLASH file

Restore EEPROM Data >> Selected EEPROM File

Restore EEPROM data successfully!

Restore FLASH Data >> Selected FLASH File

Writing FLASH data, please wait…

Restore data successfully!

Clone BMW DME completed.


LAUNCH-X431 IMMO PLUS Clone BMW DME Bench Tutorial
LAUNCH-X431 IMMO PLUS Clone BMW DME Bench Tutorial

www.x431shop.eu

Comments

Post a Comment

Popular posts from this blog

THINKCAR ThinkDiag unable to connect via Bluetooth?

Image
 My THINKCAR ThinkDiag device was unable to connect via Bluetooth and download software. The error message displayed was: "Polaczenie Bluetooth nie powiodlo sie, odtacz zlacze i sprobuj ponownie. PROBUJ PONOWNIE (Bluetooth connection failed. Please close the connector and try again. TRY AGAIN)." Solution: Fix Firmware: Navigate to "More" > "Firmware Fix" > " THINKDIAG Firmware Fix". Re-plug the Device: Unplug and then re-plug the THINKCAR OBD2 Scanner . Log in to your account again. Update the App: Ensure the ThinkDiag app is updated to the latest version. Outcome: The problem was resolved! I can now connect via Bluetooth and download the software normally. www.x431shop.eu
Read more

How To Update LAUNCH X431 GIII X-PROG 3 Software?

Image
 The Launch X431 GIII Software Update function keeps your diagnostic software & app up-to-date, you can also use it to customize your frequently used software. As a powerful chip reading and writing device, it's compatible with most X431 series tablets like X431 V+ , X431 PAD VII , X431 PRO5 , etc. How to update X-PROG 3 diagnostic software & APP? On the main diagnostic scree, tap "Software Update" to enter the update center. Check the software you want to upgrade, and then tap "Update". Once downloading completed, the software packages will be installed automatically. You will see below dialogue box once the installation is completed. Note: You may stop the process by tapping "Stop", and tap "Continue" to resume the process later. In case of network connection failure, tap "Retry". www.x431shop.eu
Read more

Solved! LAUNCH X431 PAD 7 Firmware Update Failed

Image
  Problem: The Launch X431 PAD 7 is failed to update firmware, I just follow all steps but nothing work. Ensure to update device firmware V1.5.5: Connect WIFI, ensure Internet is good. Update time will take 3 mins, ensure device with enough power at least remain more than 20 percent. Don't press POWER button while update. X431 PAD VII gives an error display: "Device no response, please retry" Please check the device whether connect success. Service busy, please retry later. What's the problem? Any ideas? Solution Please remember to connect PAD 7 with X-PROG 3 Key Programmer before upgrade. That's the reason why firmware update failed. Read also: How to update Launch X431 GIII X-PROG 3 software? Technical Support www.x431shop.eu
Read more