LAUNCH-X431 IMMO PLUS Adds 2018 Jeep Cherokee Key

 Today I’m gonna show how to add 2018 Jeep Cherokee key with LAUNCH-X431 IMMO PLUS by OBD. First of all, we may need to use X431 Key Programmer to generate remote. Next, X431 scanner will read out password for key adding.

(* LAUNCH-X431 IMMO ELITE can also refer to this process)


LAUNCH-X431 IMMO PLUS Adds 2018 Jeep Cherokee Key

Step1. Key Generation

Make sure the software is in latest version.

Check original key chip & frequency.

Vehicle remote >> American >> Jeep >> Cherokee >> Cherokee(2014–2018) keylessgo ID4A 433M

Put the new key into X431 Key Programmer coil.

Click “Generate”.

Generate successfully.


LAUNCH-X431 IMMO PLUS Adds 2018 Jeep Cherokee Key
LAUNCH-X431 IMMO PLUS Adds 2018 Jeep Cherokee Key

Step2. Read Password

After generating, open anti-theft software to add key.

IMMO >> Chrysler/Jeep/Dodge >> Automatically search

Please check if there are any other OBD communication components are installed on the vehicle. Remove it if yes and then perform diagnosis.

X431 IMMO PLUS Attention:

The vehicle information is important. It is necessary to report this vehicle information to us if there is a problem during the test.

Check vehicle info, click “OK”.

Immobilizer system detection >> Make sure the Network connection is normal >> Immobilizer system selection >> RFH/TPMS(Radio Frequency Hub-Tire) >> OK >> Special function >> Read immobilizer password(PIN code) — intelligent key/FOBIK

Performing this function may change the state of the vehicle, please exercise caution!

Please switch ignition off, and turn on emergency flasher.

The read password is: 1401


LAUNCH-X431 IMMO PLUS Adds 2018 Jeep Cherokee Key
LAUNCH-X431 IMMO PLUS Adds 2018 Jeep Cherokee Key
LAUNCH-X431 IMMO PLUS Adds 2018 Jeep Cherokee Key

Step3. Add Key

Erase ignition FOBIKs >> OK

This function erases all ignition FOBIKs currently.

Programmed to this vehicle. Place the start switch in the run state.

Enter and confirm the vehicle PIN: 1401

Click “RF-HUB replace”.

The pin unlock was successful. Continue to erase all ignition Fobiks.

All ignition FOBIKs have been erased for this vehicle.

Change Start switch to Lock state.

Program ignition FOBIKs >> OK

Use this function to program FOBIK(s) when the RF-HUB has been replaced or additional FOBIK(s) need to be added. The FOBIK(s) being programmed must be inside the vehicle near the center console during this procedure.

Please make sure that there are no wireless devices(notebook, scan tool, cell phone) within close proximity of the FOBIK(s) being programmed.

Place the start switch in the ignition lock state.

Enter and confirm vehicle PIN: 1401

Click “Check VIN(Vehicle Identification Number)”.

Have the FOBIK to be programmed readily available in your hands! Once you continue you will need get into the vehicle(if not already there) and press the unlock button within 30s.

The key Fobik should be in the vehicle near the center console when the unlock button is pressed and remain there until it is programmed.

Press and release the unlock button once on the FOBIK being programmed and then continue. Key FOBIK should be near or on the center console and remain there until programmed.

Click “OK”.

Programming ignition FOBIK, please wait…

Programming of ignition FOBIK successful.

RF-HUB replace >> OK

Use this function when the RF-HUB has been replaced.

Ignition FOBIK(s) must be programmed before running this function. Place the start switch in the Run state.

Enter the vehicle PIN: 1401

Learning VIN and vehicle configuration.

Please wait as this will take several seconds.

RF-HUB replace was successful.

The VIN and vehicle configuration have been learned. Cycle the ignition off before attempting to start the vehicle.

Completed.


LAUNCH-X431 IMMO PLUS Adds 2018 Jeep Cherokee Key
LAUNCH-X431 IMMO PLUS Adds 2018 Jeep Cherokee Key
LAUNCH-X431 IMMO PLUS Adds 2018 Jeep Cherokee Key
LAUNCH-X431 IMMO PLUS Adds 2018 Jeep Cherokee Key
LAUNCH-X431 IMMO PLUS Adds 2018 Jeep Cherokee Key
LAUNCH-X431 IMMO PLUS Adds 2018 Jeep Cherokee Key

www.x431shop.eu

Comments

Popular posts from this blog

THINKCAR ThinkDiag unable to connect via Bluetooth?

How To Update LAUNCH X431 GIII X-PROG 3 Software?

Solved! LAUNCH X431 PAD 7 Firmware Update Failed