LAUNCH X431

 Today, I want to share my recent experience using the Launch X431 IMMO Plus to programming my Peugeot 308(all keys lost). I'll guide you through the main steps (basically divided into two steps), and highlight some crucial points for a smooth operation. PS: LAUNCH X431 IMMO ELITE and X431 IMMO Plus are basically the same in IMMO function. So applies to X431 IMMO ELITE and X431 IMMO Plus . Step 1: Reading Anti-Theft Key Password The first step involved reading the anti-theft key password. It's important to ensure a proper connection between the X431 IMMO device and the vehicle. Also, make sure you have a stable internet connection throughout the process. Select the appropriate options on the device: IMMO >> Peugeot V10.22 >> Peugeot >> Anti-theft Key Password Reading >> All Lost Anti-theft Password Reading >> BSI >> Automatic Scan. A couple of things to keep in mind: Ensure the BSI Control unit voltage is sufficient. A low b...

  LAUNCH X431 ECU & TCU Programmer has been confirmed and can be used to clone BOSCH MED17.8.10 ECU. The following is feedback from a user: I recently delved into the world of ECU programming and had an exhilarating experience with the Launch X431 ECU Programmer clone. Specifically, I successfully tackled the BOSCH MED17.8.10 TC1728 ECU on the bench, and the process was a breeze, without the need for the X431 tablet. In just 2 or 3 minutes, I had the job done with ease, thanks to the user-friendly interface and detailed wiring diagram within the software. 1. Seamless Device Connection: To kick things off, I connected the X431 ECU Programmer to my computer using a USB cable. Once the connection was established, I fired up the X-431 ECU & TCU Programmer software. To quickly locate the specific ECU model, I input "med17.8.10" into the search box, and voila — I found the GreatWall Hover 62014–2018 TGI 1497 164 MED17.8.10 HW2_TC1728. Double-clicking on the...

 Renault Bosch Edc17cp19 ECU successfully read, and write back modified flash file using Launch X-prog3 and PC adapter . Modified flash. Egr & dpf off. Works nice and easy. Programmer working separately, no need xprog3 . There attached adapter. If you have xprog3, buy desktop adapter. Same functions, like programmer. Just need to go in other section. Upload modified file, to do checksum, then write. Did checksum, and problem gone.

 Accidentally it may happen to your LAUNCH X431 CRP919E device "Serial number has not been registered" issue. At this time, what should we do? Here we provide 2 solutions to fix the error. Check Device Version Settings >> About >> Version Solution 1. If the APP version is lower than V1.07_2.14, tap "Clear up" first, then upgrade the software. Solution 2. If the problem is still not been solved after cleaning up the cache, please copy these 2 APK to a SD card. Remove the cover of X431 CRP919E device , here is the SD card port. Insert the SD card. Settings >> Long press "Network" and slide up repeat 3 times. Settings(设置) >> Input 668, confirm(确定) Storage >> Install 2 APK After installing completed, re-connect to WiFi. Now the problem was solved! The error reminder has gone. Technical Support Email: Sales@X431shop.eu WhatsApp: +86 18054815707 www.x431shop.eu

 Here is the working solution to Launch CRP919E , CRP919X , CRP919I, CRP359 diagnostic scanner 'program exception' problem. Repair Guide: Preparation: Download Tool configuration Step 1: Please keep the device turned on and connect your device to the computer using a USB cable. Step 2 : Enter cmd in the bottom left corner of the computer and press Enter to open the cmd interface: Step 3: Unzip the Tool configuration folder to the outermost layer of drive D. Step 4: Switch disk directories using commands. Enter the command "D:" and press Enter (no quotes) Step 5: Go to the adb directory. Use the command "cd adb" and press enter Step 6: Upload the configuration file corresponding to the configuration file to the device. For example, if the customer has CRP919E, enter the path of CRP919E in the command. CRP919E Run this command: adbpush D:\Tool configuration\Configuration file\CRP 919E\config.xls/sdcard/, then press enter. CRP 359...

  Launch X431 ECU Programmer and X431 X-PROG3 PC Adapter streamline the cloning process of Nissan Engine Computers, specifically for models like the 2014–2017 Nissan Leaf (23740–3Nxxx-Gen1_SH72531). The beauty of this procedure lies in its simplicity — no need for an X431 tablet. Vehicle model and ECU model: i.e. 2014–2017 Nissan Leaf 23740–3Nxxx-Gen1_SH72531 How to connect: Open LAUNCH X431 ECU software, input 23740 to quickly find the corresponding ECU model, then double-click it to check the direct connect of diagram. Follow this wiring diagram to connect the Launch tool and ECU, and connect the Launch tool to the computer via USB cable. (If using It is XPROG3, you need to use XPROG3 PC Adapter in this process) Here's a concise operation guide : Step 1: Backup Original Nissan ECU EEPROM & FLASH Data. Open X431 ECU & TCU Programmer software or X-PROG3 PC software. Connect ECU. After connected, read EEPROM and FLASH data separately, and save the data af...