LAUNCH X431 Tablet Device Comparison (IMMO Elite vs Pad 7 vs X431 V+)

 Introducing the latest offerings from LAUNCH X431: the X431 IMMO Elite, IMMO Plus, X431 V+, and PAD7. Tailored to meet distinct automotive needs, IMMO Elite & IMMO Plus excel in IMMO programming, while X431 V+ & PAD7 prioritize comprehens ive diagnostics.

The following table compares the functional parameters of these four devices:

LAUNCH X431 Tablet Device Comparison

Two additional points need to be added:
X431 PAD 7 & IMMO Plus have added VW, Audi, Skoda, Seat, Benz, BMW, Porsche immo programming function and engine/gearbox clone in IMMO PROG software.

X431 V+ only supports wireless connection via Bluetooth while IMMO Plus & PAD7 can support wired connection. So that X431 V+ is unable to clone engine/gearbox, as the function needs wired connection with X-PROG 3.

LAUNCH X431 ECU Clone And IMMO Functional List:

LAUNCH X431 Tablet Device Comparison

All can work with X-PROG 3 for advanced immobilizer functions like read & write key chip, reset/coding IMMO ECU, read pin code, ECU replacement/clone, etc.

All support to read immo password, ignition on key learning, Benz/BMW/VW/Audi/Porsche immo programming, diagnostic basic function, active test and special reset service.

X431 ECU clone is covering 5000+ car models and support some unique modules while other tools cannot.

www.x431shop.eu

Comments

Post a Comment

Popular posts from this blog

THINKCAR ThinkDiag unable to connect via Bluetooth?

Image
 My THINKCAR ThinkDiag device was unable to connect via Bluetooth and download software. The error message displayed was: "Polaczenie Bluetooth nie powiodlo sie, odtacz zlacze i sprobuj ponownie. PROBUJ PONOWNIE (Bluetooth connection failed. Please close the connector and try again. TRY AGAIN)." Solution: Fix Firmware: Navigate to "More" > "Firmware Fix" > " THINKDIAG Firmware Fix". Re-plug the Device: Unplug and then re-plug the THINKCAR OBD2 Scanner . Log in to your account again. Update the App: Ensure the ThinkDiag app is updated to the latest version. Outcome: The problem was resolved! I can now connect via Bluetooth and download the software normally. www.x431shop.eu
Read more

How To Update LAUNCH X431 GIII X-PROG 3 Software?

Image
 The Launch X431 GIII Software Update function keeps your diagnostic software & app up-to-date, you can also use it to customize your frequently used software. As a powerful chip reading and writing device, it's compatible with most X431 series tablets like X431 V+ , X431 PAD VII , X431 PRO5 , etc. How to update X-PROG 3 diagnostic software & APP? On the main diagnostic scree, tap "Software Update" to enter the update center. Check the software you want to upgrade, and then tap "Update". Once downloading completed, the software packages will be installed automatically. You will see below dialogue box once the installation is completed. Note: You may stop the process by tapping "Stop", and tap "Continue" to resume the process later. In case of network connection failure, tap "Retry". www.x431shop.eu
Read more

Solved! LAUNCH X431 PAD 7 Firmware Update Failed

Image
  Problem: The Launch X431 PAD 7 is failed to update firmware, I just follow all steps but nothing work. Ensure to update device firmware V1.5.5: Connect WIFI, ensure Internet is good. Update time will take 3 mins, ensure device with enough power at least remain more than 20 percent. Don't press POWER button while update. X431 PAD VII gives an error display: "Device no response, please retry" Please check the device whether connect success. Service busy, please retry later. What's the problem? Any ideas? Solution Please remember to connect PAD 7 with X-PROG 3 Key Programmer before upgrade. That's the reason why firmware update failed. Read also: How to update Launch X431 GIII X-PROG 3 software? Technical Support www.x431shop.eu
Read more